skip to main content
Model C
Parts listed here are compatible with Model C Indoor Rowers. Model Cs were manufactured from 1993–2003.

Model C There are 51 products.

per page
Showing 26 - 50 of 51 items
  • 3,50 €

    For use with Model C, D, E and Dynamic Indoor Rowers. This is one of the small bottom seat rollers (two per machine; sold individually) that runs under the top edge of the monorail. Does not include the mounting hardware (nut, bolt and spacers) that hold the roller on the seat frame, because it can usually be reused. If you need the hardware, order part...

    3,50 €
  • 2,90 €

    For use with Model C, D and E Indoor Rowers. This is a 3-3/8 inch diameter pulley that the shock cord (part number 1731) runs over inside the Concept2 Indoor Rower. There are four per machine. Sold individually. See more info.

    2,90 €
  • 2,82 €

    For use with Model A, B, C and original D Indoor Rowers. Replacement nylon footstrap with buckle, approximately 24" long by 1" wide with a screwhole drilled approximately 7" from the buckle end. Two per machine. Sold individually.

    2,82 €
  • 2,50 €

    For use on all Model B, C, D, E and Dynamic Indoor Rowers. This is the R8 bearing located outside of the flywheel. The corresponding bearing cup (part number 1013 or 258 depending on which model you have) is sold separately. See more info.

    2,50 €
  • 2,50 €

    For use with Model C, D and E Indoor Rowers. These are the 1¼" diameter urethane pulleys that the chain runs over inside the indoor rower. There are two per machine: one is part of the traveling pulley (part number 1756); the other is mounted on a stationary axle and has two chain idler spacers (part number 1305) to keep it properly aligned. See more info.

    2,50 €
  • 2,05 €

    For use on the wooden handle originally sold on the Model A, B and C Indoor Rower. These are the black foam grips that fit on either end of the handle. Two per handle. Sold individually. Order two to have a pair. See more info.

    2,05 €
  • 1,96 €

    For use on the Model C, D and E Indoor Rower. This is the end cap for the front of the indoor rower. See more info.

    1,96 €
  • 1,80 €

    For use on all Model C, D, E, and Dynamic Indoor Rowers and the SkiErg. Using this knob instead of a nut makes it easier to take the monitor on and off of the equipment.

    1,80 €
  • 1,80 €

    For use with Model A, B, C, D, E and Dynamic Indoor Rowers. This is the hard plastic cap that goes on the rear and/or front metal legs of the indoor rower to protect your carpet or floor and keep the machine from sliding back and forth while you row. Two to four per machine, depending on age and indoor rower model. Sold individually. See more info.

    1,80 €
  • 1,66 €

    For use on the Model C, D and E Indoor Rower. This is the bumper for the rear of the monorail. See more info.

    1,66 €
  • 1,30 €

    For use with Model C and D Indoor Rowers and all SkiErgs Plastic cover for the bearing on the left side of the Model C or D Indoor Rower, opposite the flywheel, and the back side of all SkiErgs.

    1,30 €
  • 1,20 €

    For use with Model C, D and E Indoor Rowers. This is the handle hook used on the Models C, D and E Indoor Rower. To store the handle long-term, place the handle up against the flywheel housing. For ease of use before or during a workout, placing the handle in the handle hook puts the handle within easy reach. Includes hardware.

    1,20 €
  • 0,98 €

    This is part of the front monorail assembly. It is made of black plastic. For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006.

    0,98 €
  • 0,72 €

    This is the bolt for the top seat roller for all Model C, D, E and Dynamic Indoor Rowers. Order two per machine. See more info.

    0,72 €
  • 0,50 €

    Used in various places on the Model C, D and E Indoor Rower and the gray SkiErg manfactured between July 2009–July 2014.

    0,50 €
  • 0,50 €

    For use on all Model C, D, E and Dynamic Indoor Rowers as well as all SkiErgs. This is the rubber bearing cup that holds the R8 bearing on indoor rowers (part number 232, sold separately) and the 12mm bearing on SkiErgs. See more info.

    0,50 €
  • 0,25 €

    This is the 1/4-20 Nylock nut that is used with the composite handle that comes standard on the Model D and E Indoor Rowers. The corresponding U-bolt is part number 244. Order two per handle. Also used in various places on the Model C and Dynamic Indoor Rower and all SkiErgs.  See more info.

    0,25 €
  • 0,13 €

    This washer is used in the monitor mount and in the flywheel on all Model C, D, E and Dynamic Indoor Rowers and all SkiErgs. See more info.

    0,13 €
  • 0,13 €

    Used in various places on the Model C, D and E Indoor Rower and the gray SkiErg manfactured between July 2009–July 2014. See more info.

    0,13 €
  • 0,13 €

    Used in various places on the Model C, D and E Indoor Rower and the gray SkiErg manufactured between July 2009–July 2014. See more info.

    0,13 €
  • 0,07 €

    This is the nut used in the travelling pulley on the Model C, D and E Indoor Rower and in the top bracket of the gray SkiErg manfactured between July 2009–July 2014.

    0,07 €
  • 0,07 €

    Used in various places on the Model C, D and E Indoor Rower and the gray SkiErg manfactured between July 2009–July 2014.

    0,07 €
Showing 26 - 50 of 51 items